| BEFORE
YOU BEGIN:
- All products are designed for installation on the outside
of the vehicle.
- Required Items include an installation squeegee (included),
masking tape, glass cleaner, dry paper towels, measuring tape
or ruler.
- Do not apply any vinyl graphics in direct sunlight. Make
sure it is between 60 degrees and 80 degrees F
- Do not store unapplied graphics in direct sunlight - damage
may occur.
- All dirt, grease and wax must be removed from the car surface
before the decal is applied. This includes wax from mechanical
car washes, rain-x, compound, etc. Failure to take this step
may result in the decal not sticking to the vehicle surface.
CARE
AND MAINTENANCE:
Once the decal is installed, to keep it looking new, simply
wash it whenever you wash the vehicle. You can apply car wax,
clearcoat, or RainEx over the decal once it is applied. your
new decal will give you years of great looks. If you are in
cold climate be careful when using an ice scraper on any surface
where decals are applied.
| STEP
1 - UNPACK THE SHIPPING CONTAINER |
 |
Remove
the blank strip from packaging. Lay the strip flat on
a smooth table in an area that is at least 60° F and
below 80° F. The strip should be approximately 24"x60" |
| Inspect
decals for damage during shipment. We double-check all
orders are checked prior to shipment for damage. Any
damage incurred during shipping must be reported to
us within 48 hours. |
| STEP
2 - SLICE THE STRIP IN HALF (24inch kit only) |
| |
Using
a razor blade and a straight edge, cut the strip in half
(making two 12in by 60 in strips). Each 24inch kit kit has enough
material to make two windshield strips 12"x60".
|
| Be
sure when you make the cut that it is along the long
side of the strip.. |
| STEP
3 - PREPARE THE SURFACE |
| |
The
most important step during decal installation is making
sure the installation area is clean and dry. Make sure
there is NO WAX, RAIN-X, COMPOUND, lint, dust, or other
residue on the surface. Remove all wax, compound residue,
car wash protectant, etc with PREP-SOL, laquer thinners,
brake cleaner, 409, Fantastic, etc. After cleaning the
surface, go over the surface with regular glass cleaner.
Wipe it dry. |
| All
waxes, oils, and polish must be removed from the vehicle
surface to insure that the decal will stick properly
Make sure the area is at least 60° F and no hotter
than 80° F. |
| STEP
4 - MARK THE WINDSHIELD |
| |
With
a tape measure and parking pencil, measure and mark the
windshield post where the desired bottom edge will be
of the strip when installed. Be sure to measure down the
same amount on both sides of the windshield. Be sure to
check your local laws regarding placement of vinyl on
the windshield.
|
| Measuring
and marking the posts will ensure that the strip is
straight when installed. |
| STEP
5 - PLACE ONE SECTION OF THE BLANK STRIP IN PLACE |
|
With
a friend's help, take on of the blank strips, and hold
it across the windshield (turn the strip so that the edge
you cut is on top. This makes the straight factory vinyl
edge facing towards the bottom) There should be extra
on top past the top of the window.
|
| Normal
drop strips are between 4 and 6 inches. There should
be extra vinyl on top above the window.. |
| STEP
6 - TAPE IT TO THE WINDOW |
| Using
two small pieces of masking tape, temporarily hold the
strip in place by taping the bottom edge of the strip
to the windshield in the desired location. With scissors
or a razor blade, CAREFULLY cut around the sides and the
top of the windshield leaving at least 1 inch extra all
around. The extra will be removed during final installation. |
|
| The
extra will be removed during final installation |
| STEP
7 - SECURE THE STRIP |
| |
With
a friend's help, place a long piece of tape along the
bottom edge of the strip, half on the strip and half on
the window, securing it. Fold the entire strip down along
the hinged area you just made. |
| |
| STEP
8 - START REMOVING BACKING PAPER |
| Raising
the large hinged 'flap', and begin to peel the wax paper
backing off the strip (exposing the sticky side of the
decal). Spray a light mist of water (water only, NO SOAPY
SOLUTIONS!!!!) |
|
| Using
a spray bottle filled with regular water is important.
Soapy solutions tent to keep the decal wet and may lead
to the strip flying off at high speeds. |
| STEP
9 - BEGIN DECAL APPLICATION |
| |
With
the wax paper backing peeled half way downward, begin
to apply the sticky side of the strip to the vehicle surface
with the Free application tool enclosed. Besure to use
even strokes horizontally across the decal. |
| Continue
to spray a LIGHT coating of water onto the window surface.
Too much water will lead to the strip not drying properly.
Not enough water will make it stick prematurely. |
| STEP
10 - CONTINUE INSTALLATION |
| Continue
smoothing out the strip with long hoizontal strokes, starting
at the top and working towards the bottom. Continue to
remove the backing paper as needed. |
. |
| Only
remove the wax paper backing as needed. The sticky side
of the decal should be covered until installation. This
will keep it from getting dirty and sticking to the
vehicle surface prematurely. |
| STEP
11 - TRIM AROUND THE WINDSHIELD POST |
| |
Once
the entire strip is applied, use a razor blade to trim
the strip at the edge of the window. Take your time and
be patient. Cutting it too short will result in a rough
edge. Cutting it too long may result in it getting caught
on something. |
| |
| STEP
12 - FINISH INSTALLATION |
| Once
the strip has dried for at least 2 hours, apply wax or
rain-x over the strip and window surface. This will keep
the wipers from damaging the strip during normal use. |
. |
| Most
bubbles will dissipate within 3 weeks of installation
due to sunlight. |
All
of our products are custom made to order. There are no refunds,
no exchanges and no returns on any of our products. If you
destroy the decal during installation, we may offer you a
replacement at a reduced cost. In order to qualify for a lower
cost replacement, you must send us the damaged decal. Management
reserves the right to modify this policy.
This page is protected by U.S. and International Copyrights.
Any duplication or distribution of this information in any
form is illegal. We have successfully prosecuted content theft
in the past and aggressively pursue violators. The information
has been imbedded with searchable phrases which can be traced
to any website using them.
|
